Home < Precision Calibration Standards < Coaxial Calibration Kits < 2650 Series
7mm VNA Calibration Kits
2650 Series These coaxial VNA calibrtion kits are configured for the Open-Short-Load-Thru (OSLT) calibration technique using sliding loads. In this model series fixed termination kits are also offered as a simple, economical option to the standard and expanded kits. Data Sheet 2Z-022P Features Fixed Termination Kits • Simple, Economical Standard Kits • Broad VNA Coverage • Includes Applicable Test Port Adapters, Spare Collets and Extractor Expanded Kits • Sliding termination • Connector Gage Description Maury's 7mm calibration kits are designed for use with vector network analyzers (VNAs) supplied with 7mm, 3.5mm or 2.92mm test set connectors and cables. With these kits you can make error corrected measurements of devices supplied with 7mm connectors from 45 MHz to 18 GHz. These kits include a full complement of calibration standards: shorts, opens, fixed and sliding loads1. Rugged test port adapters and 7mm to 3.5mm phase matched adapters are also provided where applicable. A connector gage1 for checking contact pin locations prior to making measurements, and a torque wrench1 for accurately tightening connector junctions, are also included. All required calibration standards, adapters and accessories along with the applicable software medium (cartridge or 3-1/2" disk) containing the calibration constants and operating instructions, are supplied in an attractive foam-lined wooden instrument case. Each kit includes a full complement of calibration standards and accessories (listed below), and the software (3-1/2" disk or cartridge) needed to easily load the calibration constants into your VNA. Connector Description 7mm connectors are precision air interface hermaphroditic connectors that are rated from DC to 18 GHz. They have an air line size of 0.1197 inner diameter and a 0.2756 outer diameter. There are basically two configurations; 1) GPC7 (commonly referred to as APC7) which incorporates a bead support and, 2) LPC7 which is a beadless connector. Model Chart Select the calibration kit number appropriate for your VNA test set and cable connector. Model VNA Test Set and Cable Connectors Kit Type Software Medium 2650F08 Agilent 8510A/B 7mm Fixed Term. Cartridge 2650F Agilent 8510A/B 7mm Expanded 2650H 3.5mm 2650J Agilent 8510C 3.5mm Expanded 3-1/2" disk 2650M Agilent 8720 2650P Agilent 8753 7mm Fixed Term. 2650W Anritsu 360 2.92mm 2 Expanded 2650X Anritsu 37000 Options: 01 Adds one (1) 2653S30 Air Line to 2650F, H, J, M, W, and X kits. 2650F02 A sliding load kit without the connector gage and torque wrench. 2650F08 A fixed termination kit without the adapters, sliding termination and connector gage. 2650P16 Includes a data disk for Agilent 8753A/B/C.	2650F21 Equipment Provided In Kits (2650F, H, J, M, W, X) 1 ea. Fixed Short, 7mm 1 ea. Open Circuit, 7mm 2 ea. Fixed Termination, 7mm 1 ea. Sliding Termination, 7mm 2 ea. Adapter, 7mm Test Port to NMD3.5mm (female) 1 1 ea. Adapter, 7mm to 3.5mm (female)* 3 1 ea. Adapter, 7mm to 3.5mm (male)* 3 1 ea. Connector Gage Kit, 7mm (push-on type) 1 ea. Torque Wrench, 0.75-inch hex, 12 in/lb 1 ea. Software Configuration Medium (Containing Circuit Constants) 1 ea. Collet Extractor 4 ea. 7mm six-slot Collets (Spare Parts) 1 ea. Instrument Case 1 ea. Operating Instructions Equipment Provided In 2650P Kits 1 ea. Fixed Short, 7mm 1 ea. Open Circuit, 7mm 2 ea. Fixed Termination, 7mm 1 ea. Instrument Case 2 ea. Operating Instructions Available Accessories (Not Provided) Offset Shorts Series 2049. Precision Mismatches Series 2611 in values up to 2:1 VSWR Precision Two-Port Standard Set Model 2654B * Phase matched set.
1 Not provided in fixed termination kits. 2 The 3.5mm connectors are mating compatible with 2.92mm (K). The resulting junction is calibrated out and is not critical. 3 Not provided in 2650F, 2650F02, or 2650F08 kits.
Copyright 2006 by Maury Microwave Corporation. All rights reserved.